800-150 Dumps Guarantee You Pass 800-150 Exam Easily

As new threats and vulnerabilities emerge, the 800-150 exam is updated to reflect the latest trends in Cisco Certified Field Technician (CCT). By using 800-150 exam dumps questions, you can ensure that you're staying up-to-date with the latest exam content and are fully prepared to address new challenges in Supporting Cisco Devices for Field Technicians (FLDTEC). Cisco 800-150 exam dumps questions can help you optimize your preparation and ensure that you're fully prepared for the exam. Practice free Cisco 800-150 exam dumps questions below.

Page 1 of 3

1. Why is it important to verify the update status after the initial upgrade process when upgrading firmware on a Cisco UCS C-Series server using the Host Upgrade Utility?

To generate a report for compliance documentation

To confirm that all intended components were successfully updated

To ensure compatibility with third-party applications

To activate the new licenses associated with the firmware

 Loading...

2. Which operating system powers the Cisco Nexus series of switches and is optimized for modern data center deployments?

IOS

IOS XE

IOS XR

NX-OS

 Loading...

3. DRAG DROP

Drag and drop the Cisco collaboration components from the left onto the corresponding descriptions on the right.

 Loading...

4. DRAG DROP

Drag and drop the characteristics from the left onto the corresponding categories of MDS switch on the right.

 Loading...

5. Which command is used to determine if there is sufficient space in the memory of a device before installing a new Cisco IOS image?

show file-system

show storage

show memory

show flash:

 Loading...

6. DRAG DROP

Refer to the exhibit.





Drag and drop the names of the field-replaceable units from the left onto the corresponding letters on the image of the Cisco Catalyst 9400 modular switch.

 Loading...

7. What must be verified before installing or replacing DIMMs in a Cisco UCS server?

Compatibility of the DIMM with the current firmware version of the server

Current DIMM configuration and population order

Exact type, speed, and capacity of the DIMM

Maximum supported DIMM capacity for the server model

 Loading...

8. What is the primary purpose of changing the configuration register when performing password recovery?

To erase the entire configuration

To ignore the startup configuration

To unlock all user accounts

To enable advanced debugging features

 Loading...

9. Which protocol should be analyzed when troubleshooting call quality between IP phones?

SIP

SCCP

323

RTP

 Loading...

10. What is the purpose of a subnet mask?

Distinguishes the network and host segments

Provides encryption for network traffic

Determines the next-hop router

Aids in route prioritization

 Loading...

Page 2 of 3

11. DRAG DROP





Drag and drop the functions from the left onto the corresponding internal memory components on the right.

 Loading...

12. DRAG DROP

Drag and drop the Cisco UCS components from the left onto the corresponding functionalities on the right.

 Loading...

13. What is the first action that must be taken before removing a standby supervisor module from a Cisco MDS 9700 Series Switch?

A. Shut down the entire switch.

B. Put the module into out-of-service mode.

C. Disconnect all network interface cables.

D. Perform a manual failover to the standby supervisor.

 Loading...

14. Refer to the exhibit.





Which CLI show command identifies the serial number on a router?

show inventory

show idprom

show version

show platform

 Loading...

15. Which component serves as the central management and communication core and provides a single point of management via Cisco UCS Manager in a Cisco UCS environment?

Nexus 9000 Series Switch

UCS E-Series server in ISR platforms

MDS 9000 Series SAN Switch

UCS Fabric Interconnect

 Loading...

16. Which term describes the physical range of radio frequency coverage provided by an access point in a wireless topology?

Service Set Identifier (SSID)

Basic Service Area (BSA)

Wireless LAN (WLAN)

Wireless LAN Controller (WLC)

 Loading...

17. Which step must be performed immediately after disconnecting the network cable when replacing an SFP transceiver module?

Observe the port status LE

Disconnect the SFP latch.

Reinstall dust plugs in the optical bores.

Install the replacement SFP module.

 Loading...

18. What is the function of an access layer device?

Provides high-speed data transport between buildings or different parts of the campus

Serves as the entry point for end-user devices to connect to the network

Provides secure external access to internal network components

Connects remote offices to the main corporate network

 Loading...

19. DRAG DROP

Drag and drop the functions from the left onto the corresponding Cisco data center technologies on the right.

 Loading...

20. Which two settings are standard Cisco console connections when configuring a terminal emulator to connect to the console port of a Cisco switch? (Choose two.)

Stop bits: 2

Flow control: Hardware

Speed (baud rate): 9600

Data bits: 8

Parity: Even

 Loading...

Page 3 of 3

21. Which two components are accessed by removing the chassis cover on Cisco Catalyst 8000 Series Edge platforms? (Choose two.)

Transceivers

Network Interface Modules

DIMMs

SSDs

Fan trays

 Loading...

22. Refer to the exhibit.





What is the redundancy implementation in this Cisco UCS architecture?

Redundancy is achieved through dual fabric interconnects, providing separate paths for FCoE, FC, and LAN traffic.

Redundancy is limited to the uplink connections, with no failover capabilities between the fabric interconnects.

The system uses a single point of connectivity, relying on internal redundancy within each UCS chassis.

Redundancy is implemented at the chassis level only, with chassis 1 acting as a backup for chassis 2.

 Loading...

23. Which deployment scenarios are Cisco 8000 Series routers primarily designed for?

remote branch offices and retail locations

service provider and web-scale networks

small business and home office networks

campus LAN access and distribution layers

 Loading...

24. Which command prompt commands provide the most thorough network diagnostic information when troubleshooting connectivity issues between a Windows PC and a Cisco device?

ipconfig /all ping

netstat -a netsh wlan show interfaces ipconfig /release ipconfig /renew

ping tracert netstat

nslookup arp -a route print

 Loading...

25. DRAG DROP

Drag and drop the actions that must be taken after installing an E-Series server from the left into order on the right.

 Loading...

26. Which mode must the console terminal of the device be in before a prewritten configuration is pasted to transfer the configuration from an old device to a new one?

Interface configuration mode

Global configuration mode

Privileged EXEC mode

User EXEC mode

 Loading...

27. What is the primary purpose of backing up the endpoint configuration prior to replacing the device?

To troubleshoot network connectivity issues

To update the firmware of the device

To generate a performance report for the old device

To restore settings on the new device after replacement

 Loading...

28. Which type of license is locally managed and does not require external tools for management?

Hybrid licenses

PAK licenses

RTU licenses

Smart licenses

 Loading...

29. DRAG DROP





Drag and drop the functions from the left onto the corresponding devices on the right.

 Loading...

30. Which step must be taken to minimize data traffic impact when replacing a fabric interconnect?

Use the fabric evacuation procedure on the subordinate fabric interconnect.

Disable high availability before replacement.

Remove all cable connections at once.

Power down both fabric interconnects simultaneously.

 Loading...

 Loading...