Advance Your Career by Using Online FlashArray Implementation Specialist Dumps

Obtaining the FAIS FlashArray Implementation Specialist certification can help you demonstrate your expertise in Pure Storage solutions and advance your career in related industry. Using FlashArray Implementation Specialist dumps as part of your study plan can help you identify knowledge gaps, improve your exam-taking skills, provide immediate feedback, and increase your chances of passing the FlashArray Implementation Specialist exam. Pure Storage FlashArray Implementation Specialist exam free dumps questions are available below.

Page 1 of 3

1. An Implementation Engineer performs a controller upgrade.

What is the command to check I/O health?

purehost list --all

pureport list --initiator

purehost monitor --balance

 Loading...

2. An Implementation Engineer is onsite to add two 4-port FC cards to a FlashArray//X20R3. In what state should the controller be in before performing the card add procedure?

Primary

Secondary

Standby

 Loading...

3. When performing an install on a FlashArray, what step should be taken first?

CT0 configuration

CT1 configuration

Code upgrade

 Loading...

4. Which enablement feature will cause Mirrored Write statistics to appear in the Analysis section of the FlashArray Purity 6.x GUI?

FA File

ActiveCluster (AC)

ActiveDR

 Loading...

5. Which default speed FC SFPs are shipped in FlashArray//XCR4 FC arrays?

16

32

64

 Loading...

6. At the completion of an upgrade, which command is used to send phonehome logs?

purelogs --send-all

purearray phonehome --send-logs

purearray phonehome --send-today

 Loading...

7. Which I/O card type is compatible across all FlashArray models?

10GBaseT

iSCSI

FC

 Loading...

8. In a situation where FC cards need to be re-used during a controller upgrade, which is a valid transfer path?

M>XR2

M > XR2/3

XR2 > XR3

 Loading...

9. A customer has a FlashArray X20R3 with 22/22 data packs in the chassis at 80% space usage and wishes to swap one of the data packs for a 45TB pack.

What step needs to be taken to facilitate this consolidation?

Send a DirectFlash Shelf without any additional capacity.

Send a DirectFlash Shelf with a 63TB of temporary extra capacity.

Reduce array space usage to allow for the evacuation of the 22TB packs.

 Loading...

10. A customer has purchased a FlashArray//XL.

What power cables are required in order to connect this array to rack PDUs?

2 x C13/14

4 x C13/14

4 x C19/20

 Loading...

Page 2 of 3

11. A dark site customer requests an evacuation of SH01 on a FlashArray/M50.

What is an appropriate next step?

Use the evac_checks script.

Ensure that usable capacity is less than 80%.

Ensure that usable capacity is less than 90%.

 Loading...

12. For FlashArray//XL, which PCIe card slot is reserved for control upgrades?

5

6

7

 Loading...

13. What should an Implementation Engineer do when installing rails in a threaded-hole rack?

Use the positioning studs

Install the rails as is

Make an adjustment to the rack

 Loading...

14. An Implementation Engineer is scheduled to install a FlashArray and a DirectFlash Shelf (DFS).

What action should the Implementation Engineer perform?

Refer to the “Recommended DFS Versions for Purity Releases” KB and upgrade Purity on the FlashArray and DF

Install the Array and DFS with the Purity that shipped and have Support upgrade remotely.

Only upgrade the Purity on the FlashArray and then attach the DF

 Loading...

15. What is the speed of the Ethernet ports to connect a FlashArray //E to a DFS?

40G

25G

100G

 Loading...

16. For FlashArray//XL, which 2 PCIe slots should be used for DFS connectivity?

0 and 4

0 and 6

1 and 7

 Loading...

17. An Implementation Engineer is onsite to install a new DFM data pack (DP) to CH0.BAY10-CH0.BAY19 of a FlashArray.

After adding the drives to the chassis, which command should the Implementation Engineer run to verify if the new DP is in a wide write group?

find_drive.py

puredb list drives

puredrive list --pack CH0.BAY10

 Loading...

18. The customer has completed the installation document and has stated that the proxy server address is “10.24.18.120”.

What additional information is required?

Credentials and port number

Protocol prefix and credentials

Protocol prefix and port number

 Loading...

19. After upgrading Purity during a new installation, which command should an Implementation Engineer run to determine what version of Purity will be loaded at the next boot of the FlashArray?

purearray list --controller

pureversion -a

pureboot list

 Loading...

20. What command should be used to check the shelf cable connections?

purearray list --shelf

purehw list --enclosures

storage_view.py config

 Loading...

Page 3 of 3

21. A FlashArray//XR2/3 has an Ethernet mezzanine (EMEZZ), what are the interface names of the ports on the mezzanine?

ETH6, ETH7, ETH8, and ETH9

ETH8, ETH9, ETH10, and ETH11

ETH10, ETH11, ETH12, and ETH13

 Loading...

22. In a situation where iSCSI cards need to be re-used during a controller upgrade, which is a valid transfer path?

XR2 > XR3

M > XR2/3

M>XR2

 Loading...

23. What hardware should the Implementation Engineer find in the upgrade kit in order to perform an //X to //XL NDU?

2 QSFP cables / 3 Mellanox cards / 20 DFMDs

3 QSFP cables / 4 Mellanox cards / 10 DFMDs

4 QSFP cables / 2 Mellanox cards / 20 DFMDs

 Loading...

 Loading...