2023 Network Appliance NS0-184 Exam Dumps Questions

Category:

Comments:

0 Comments

Post Date:

November 25, 2023

Network Appliance certification is a highly valuable and sought-after certification for IT professionals seeking to enhance their knowledge and expertise. NS0-184 exam is specifically designed to validate the skills required to configure and maintain the Network Appliance NCSIE ONTAP Certification platform, which is widely used by businesses around the world. These NS0-184 exam dumps questions are specifically designed to help you prepare for the exam by testing your knowledge and providing you with valuable insights into the types of questions that you will encounter. Test free Network Appliance NS0-184 exam questions below.

Page 1 of 12

1. Which two statements are true about the LIFs that are used for a cluster peer relationship? (Choose two.)

The MTU size must be set to 9000 bytes on all the LIFs used for the cluster peering.

The LIFs must use the default intercluster service policy.

The LIFs must be in dedicated broadcast domains an IPspaces.

At least one LIF per node is required on each cluster.

2. Exhibit:

Your ONTAP cluster shows the cluster network errors that are shown in the event log.

What is used by ONTAP software to log the errors that are shown in the exhibit?

BGP

AutoSupport

EMS

SNMP

3. While testing storage failover, you receive an error message indicating that you have a disk inventory mismatch.

What is a reason for the error message?

unsupported disks

cabling problems

Flash Cache problems

unowned disks

4. A customer requires encryption at rest on every node root volume.

In this scenario, which two encryption solutions will fulfill this requirement? (Choose two.)

NVE

IPsec

NAE

NSE

5. You have completed the installation and verification of the cluster for a customer.

What is required to complete the event?

Present the customer with the posters included in the boxes.

Call your manager to let them know that you are finished.

Have the customer call NetApp Support to let them know that the installation is complete.

Have the contact sign a document saying that the installation is complete.

6. You have just replaced a FAS controller with a new controller and installed the appropriate licenses for the new FAS controller.

What are two ways to remove unused licenses in this situation? (Choose two.)

Use OnCommand Unified Manager.

Use OnCommand System Manager.

Use the cluster license clean-up -unused command.

Use the system license clean-up -unused command.

7. Select the Exhibit tab.

Your customer has an AFF A300 installed. They ask you to configure the e0a and e0b ports to use the FC protocol. Referring to the exhibit, which statement is correct in this scenario?

These ports are used for the Ethernet uplink into the customer’s network.

The configuration of these ports can only be done by OnCommand System Manager.

These ports are used for the cluster interconnect.

Use the ucadmin command to configure these ports as FC ports.

8. A customer has a stack of shelves with both DS4243 shelves and DS4246 shelves. The customer wants to replace the DS4243 shelves with new DS4246 shelves.

What would you advise the customer in this scenario?

Convert the ACP communication from out-of-band to In-band channel.

Remove the ACP cabling from the stack before adding the new shelves.

Remove the DS4243 shelves, but you must add the new DS4246 shelves to a new stack.

Configure the shelf IDs of the new DS4246 shelves to match the existing DS4246 shelves.

9. You want to enable secure communication with the SP or BMC through CA-signed certificates.

Which two certificate types must be installed in this scenario? (Choose two.)

cluster certificate

server certificate

root CA certificate

ONTAP certificate

10. You installed a new FAS9000 with SAS disk shelves. You want to use write cache in this environment.

In this scenario, what should you do to accomplish this task?

You need to buy an SSD and set it up as a storage pool for write cache that is used for the aggregate that you need.

You need to buy an SSD and set it up as a Flash Pool for write cache that is used at the node that had an SS

You need to set up the caching policy as your requirement by using the Flash Cache NVMe module.

You need to buy an SSD and set it up as a Flash Pool for write cache that is used at the aggregate that had an SS

Page 2 of 12

11. You are expanding an existing cluster that uses BES-53248 cluster interconnect switches. You connected the new controllers to ports 0/17 through 0/20. However, you are unable to join the new nodes to the cluster.

Which action must be taken to solve the problem?

Install the license file.

Install the CSHM configuration file.

Install the reference configuration file.

Reboot the controllers.

12. After the Installation of a new NetApp FAS system, you use theNetAppDocs tool for site design documentation.

In this scenario, in which three document formats would you create an inventory report? (Choose three.)

.docx

.html

.pdf

.ps

.xlsx

13. A customer using ONTAP or later needs a node-specific license key.

What will the license key be matched against?

controller chassis serial number

controller NVRAM

controller system ID

controller serial number

14. You are a NetApp Professional Services engineer, employed by NetApp. You have just completed an ONTAP cluster installation. You need to collect the relevant configuration information to enable the Service Event Report (SER) to be created.

Which tool would you use to accomplish this task?

Active IQ scheduled reports

NetAppDocs output report

ONTAP System Manager

Active IQ Config Advisor worksheet

15. Before installing an 8-node cluster for a customer, you want to validate compatibility with existing hardware.

Which two tools would you use to validate the configuration? (Choose two.)

Interoperability Matrix Tool

Active IQ System Manager

Hardware Universe

Active IQ Config Advisor

16. You are preparing for the installation of a new AFF A400 system with NS224 NS224 storage shelves. You want to gather information on the connectivity options for the external shelves.

In this scenario, which NetApp tool would you use for this task?

Hardware Universe

Active IQ Config Advisor

Active IQ Unified Manager

Interoperability Matrix Tool

17. According to NetApp best practices, how many NTP servers should you associate with an ONTAP cluster?

18. You are setting up a peer relationship between two ONTAP clusters.

In this scenario, which two statements are true regarding authentication?

Peering authentication status can be verified with the cluster peer show command.

Peering authentication can be configured using LDAP users and groups.

Peering authentication is required before enabling peering encryption.

Peering authentication can use an ONTAP generated passphrase.

19. Before starting a base installation on an AFF A400, you need to find out the default cluster interconnect ports for the AFF A400 controllers.

In this scenario, which three resources would you use to find this information? (Choose three.)

Hardware Universe (HWU)

Interoperability Matrix Tool (IMT)

hardware installation setup poster

AFF FAS Documentation Center

Active IQ Unified Manager

20. You want to verify a clustered Data ONTAP installation at a customer site. In this scenario, which tool you use?

Config Advisor

Solution Builder

Cluster Config Builder

Synergy

Page 3 of 12

21. When used as a cluster interconnect switch, what is the function of the Cisco Nexus 3132Q?

It is a 40 Gb Ethernet switch.

It is a 10 Gb FCoE switch.

It is a 32 Gb Fiber Channel switch.

It is a 1 Gb Ethernet switch.

22. Multiple customers want to access a cluster from different domains that may contain duplicate IP addresses.

In this situation, which feature should you use?

IPspaces

interface groups

VLAN

logical interfaces

23. 1.Your customer currently has a 4-node AFF A400 cluster that runs ONTAP 9.8, with two NS224 shelves that are connected to each HA pair. The customer needs to add additional capacity to the cluster.

Which two actions would enable the customer to accomplish this task? (Choose two.)

Connect the new NS224 shelves to the existing NS224 shelves and adjust the shelf IDs.

Connect the new NS224 shelves to the existing Cisco Nexus 3232C switches.

Deploy a new AFF A400 to the cluster.

Deploy new, dedicated, storage switches for the new NS224 shelves.

24. You are ready to purchase a new FAS8200 six node cluster. In this scenario, which three switches are supported as NetApp cluster interconnect switches.

Cisco nexus 5596UP

Cisco Nexus 5548UP

Cisco Nexus 3132Q-V

Cisco CN1610

Brocode 7840

25. You need to move a LIF to another port or to another node which requires certain configuration settings.

Which two conditions should be verified before beginning this operation? (Choose two.)

The destination node and ports must be operational and able to access the same network as the source port.

The only ports that can be added to a failover group are VLANs.

A failover group must exist for the LIFs.

The destination port must be a member of a different broadcast domain.

26. Which technology allows NetApp to ship replacements for defective parts automatically?

SLDIAG

Call Home

AutoSupport

27. According to NetApp best practices, which tool should be used to verify the system configuration?

Synergy 6.1

OnCommand System Manager

Config Builder

Config Advisor

28. You are cabling two Cisco 3232C switches for the cluster interconnect of a 4-node AFF A800 cluster.

Which pair of ports are used to cable the Inter-Switch Link (ISL) between the switches?

1/21 to 1/24

0/13 to 0/16

1/31 and 1/32

0/1 and 0/2

29. Node 3 has taken over Node 4. You are attempting to access Node 4 on its management interface but cannot do it.

In this scenario, how would you access Node 4’s management interface?

You must use the Service Processor; node management LIFS do not fall over between nodes.

You have not waited long enough for the failover timeout for a node management LIF; there is a broadcast domain configured for this situation.

You should use SSH directly to one of the cluster interconnect switches; from there, you can use SSH to the node management on node 4.

Connect to the node management on Node 3 and then use the HA interconnect to access node 4.

30. You have just finished installing and configuring an ONTAP cluster for a customer.

In this scenario, which product collects information and produces site documentation?

NetAppDocs

Inventory Collect Tool

SnapGathers

Active IQ OneCollect

Page 4 of 12

31. You are dispatched to install a new cluster with six AFF A300 nodes. While running Config Advisor, you determine that there is a newer firmware version for 48 SSDs.

Which statement is correct in this scenario?

Prior to leaving the site, tell the customer that a later firmware exists for those disk drives, but that the upgrade will provoke downtime.

Unless the customer advises otherwise, leave the firmware alone and document the version of ONTAP being used to explain the issue.

Unless the customer advises otherwise, upgrade the firmware on the SSDs to clear the Config Advisor error.

Prior to leaving the site, advise the customer that the firmware is included in the version of ONTAP that they downloaded.

32. You have completed a base installation and system registration of an AFF A250 system, but you notice that you have one failed drive. Neither “un-failing” nor reseating the drive helped to repair it. You must ensure proper replacement of the failed drive.

In this scenario, which two actions should you take? (Choose two.)

Ask the customer to open a technical case with NetApp Support.

Ask the customer for a drive with the same capacity and replace it.

Run Active IQ Config Advisor to collect all the logs on the system.

Power off the system until the drive has been replaced.

33. You are preparing for the installation of a new ONTAP 9.8 cluster and need to get the preinstallation information from the customer.

In this scenario, which NetApp tool would you use to create a configuration spreadsheet template for the deployment?

Interoperability Matrix Tool

ConfigBuilder

Active IQ Config Advisor

Active IQ Unified Manager

34. A 4-node cluster has connectivity for both block and file access. Nodes 1 and 3 are used for file access, and nodes 2 and 4 are used for block access. During routine maintenance, node 4 is switched off and the LIFs are migrated to other nodes. Upon investigation, you see that the LIFs that serve file traffic have moved to alternative ports.

However, LIFs that serve the block have not migrated. In this scenario, what is happening?

The failover group is configured incorrectly.

The fiber switch is configured incorrectly.

There is a faulty SF

The LIFs that serve the block protocol do not failover.

35. A customer is settings up a new cluster. The customer notices that there are many management ports on the cluster. The customer is know the purpose of the node management network LIF.

What do you tell customer in this scenario?

The node management LIF provides multiple IP address for managing a particular node in the cluster at the hardware level and is used for system maintenance.

The node management LIF is associated with a storage virtual machine (SVM) and is used for communicating with client.

The node management LIF provides a dedicated IP address for the entire cluster and can fail over to any node management or data port in the cluster.

The node management LIF provides a dedicated a IP address to managing a particular node in the cluster and is used for system maintenance.

36. A customer wants to graphically manage a new clustered Data ONTAP system.

Which tool should the customer use?

System Setup

OnCommand System Manager

HostAgent

StorageGrid

37. A customer has a current AFF ASA A700 cluster and they want to expand the cluster by adding a second AFF ASA A700 HA pair.

In this scenario, which step would be required to accomplish this task?

Enable ALUA between the two HA pairs to allow cluster backend traffic.

The customer will need to create a separate cluster for the second AFF ASA A700 pair.

Install a BES-53248 cluster switch and convert the AFF ASA A700 from a switchless to switch cluster.

Install a Brocade FC switch and create zoning between the original cluster and the new cluster.

38. You are adding two new nodes to an existing switchless 2-node cluster.

In this scenario, which two statements are true? (Choose two.)

You must make sure that the existing nodes are healthy and that all cluster links are up

You need to schedule downtime to add these two nodes

The existing cluster must use clustered Data ONTAP 8.1 or later software

You first need to install the cluster interconnect switches to the existing cluster

39. You are installing a new six-node ONTAP 9.8 cluster. You have completed the initial configuration of the cluster interconnect switches and the ONTAP cluster.

In this scenario, which feature should you enable?

cluster switch logging

cluster switch health monitor

IPv6 on all cluster ports

data center bridging protocol

40. You are setting up a new cluster. The customer notices that there are many management ports on the cluster. The customer wants to know the purpose of the cluster management LIF.

In this situation, what should you tell the customer?

The cluster management LIF provides a dedicated IP address for the entire cluster and can fall over to any port in the cluster that Is available in the broadcast domain.

The cluster management LIF provides a dedicated IP address for managing a particular node in the cluster and is used for system maintenance.

The cluster management LIF is used to carry Intracluster traffic between nodes In a cluster and must be created on a 10GbE network port.

The cluster management LIF provides multiple IP addresses for the entire cluster and can fall over to any cluster or intercluster ports.

Page 5 of 12

41. You are asked to install a 6-node cluster of FAS8080 controllers. The installation has been completed and Config Advisor shows no warnings or errors. The customer can ping and access the controller.

Which statement is true in this scenario?

This installation has not been completed successfully until you have confirmed that SSH is enabled.

This installation has not been completed successfully until the customer and NetApp Support have received a minimum of three AutoSupport messages.

This installation has been completed successfully only if you have confirmed that the configuration is correct.

This installation has been completed successfully, because Config Advisor would identify the missing configuration.

42. Which three conditions would prevent a normal giveback operation? (Choose three.)

established NFS sessions

continuous SnapMirror relationships

LUNs mapped with ALUA

established CIFS sessions

presence of failed disks

43. At NetApp, what does the acronym VLDB mean?

volume location database

virtual lif direct broadcast

virtual location database

very large database

44. You have completed the installation of a 4-node cluster. The customer did not purchase management switches and will not allow your laptop on the network.

In this situation, what are two valid procedures that will allow you to collect the Config Advisor output? (Choose two.)

Bring a switch that allows you to connect your laptop to all the switches and controllers.

Connect to a single controller in the cluster since it can run commands on every node.

Ask the customer to install and run Config Advisor on one of their PCs on the network.

Connect four USB serial cables to your laptop to allow you to connect to all four controllers.

45. A new system fails to boot or has error messages indicating a problem with the system board memory.

What is the preferred method for diagnosing hardware problems in this scenario?

Verify the console output in system shell.

Run Config Advisor.

Run the appropriate SLDIAG test.

Run the node scope sysconfig Ca command.

46. Your customer regularly schedules disaster recovery tests to ensure the high availability capabilities of the ONTAP cluster.

In this scenario, which two commands would you use to perform this test? (Choose two.)

system node run -node NetApp-Cluster-02 -command cf takeover

storage failover giveback -of-node NetApp-Cluster-02

system node run -node NetApp-Cluster-02 -command cf giveback

storage failover takeover -of-node NetApp-Cluster-02

47. In a 4-node cluster, what is function of the HA interconnect? (Choose the best answer.)

It provides the ability to relocate the aggregate ownership.

It provides the ability to synchronize the cluster configuration.

It provides nondisruptive operations and fault tolerance.

It provides the ability to migrate a data aggregate to any node in the cluster.

48. Which statement describes an SVM?

An SVM is a node in the cluster

An SVM is a storage volume type

An SVM is a logical device that shares data

An SVM is a logical network interface

49. Which NetApp tool relies on PowerShell to produce a comprehensive handover report to the customer?

Active IQ

Config Advisor

NetAppDocs

Fusion

50. You are preparing for a new installation. While determining the most suitable version of ONTAP software to deploy, you want to verify the ONTAP 9 release cadence to ensure that you are deploying a Long Term Service (LTS) release.

In this scenario, where would you find this information?

Visit the Hardware Universe site

Visit the Interoperability Matrix Tool site

Visit the NetApp Support site

Visit the ONTAP 9 Documentation Center site

Page 6 of 12

51. You are performing a basic clustered Data ONTAP installation and have configured all data and cluster interconnect port configurations. However, flow control options have not yet been set.

In this scenario, what are appropriate flow control recommendations?

Flow control should be turned on for all data ports, cluster interconnect ports, and switches.

Flow control should be turned off for all data ports, cluster interconnect ports, and switches.

Flow control should be turned off for all data ports and cluster interconnect ports, but should be left on for all switches.

Flow control should be turned on for all data ports and cluster interconnect ports, but should be left off for all switches.

52. Which two switch operating system are supported on ONTAP cluster switches? (Choose two.)

Brocade FOS

Cisco NX-OS

Cisco IOS

Broadcom EFOS

53. Which hot-swappable transceiver is required to obtain full performance from a Cisco Nexus 3232C cluster-interconnect switch?

SFP

QSFP+

QSFP28

SFP+

54. A customer learns that a certain NetApp tool allows remote data collection, intelligent core file handling, and notification of down storage controllers for technical support analysis and troubleshooting.

What is the name of this tool?

RSA

HWU

Synergy

HW Assist

55. You are preparing to add a 2-node AFF A250 system to an existing 4-node AFF A800 cluster with Cisco Nexus 3232C switches. The cluster switches are currently running the Cluster-HA RCF.

In this scenario, which two steps are required to install the AFF A250 system? (Choose two.)

Load the Storage RC

Cable the AFF A250 nodes to the next free ports on the switch.

Cable the AFF A250 nodes to the breakout ports on the switch.

Load the Cluster-HA-Breakout RC

56. A customer has a six-node cluster running NFS and FCP. The customer wants to add nodes to the cluster.

How many nodes would be added in this scenario?

57. You are installing a new ONTAP 9.8 cluster by using System Manager Guided Setup.

In this scenario, which IP address is optional?

node A IP address

node B IP address

gateway IP address

cluster IP address

58. Your customer is migrating data from a legacy FAS8020 system that runs ONTAP 9.5 software to a new AFF A250 MetroCluster over IP configuration.

In this scenario, which two methods would be supported to migrate the data? (Choose two.)

Perform a controller swap from the FAS8020 to the AFF A250s.

Create a 4-node cluster on one side and use the vol move command to migrate the data.

Use a host-based copy migration method.

Configure a SnapMirror copy between the FAS8020 and the AFF A250 systems.

59. You want to add two new nodes to an existing 4-node cluster.

In this situation, what must be considered regarding the cluster interconnect?

When a new node joins a cluster, IP addresses are generated automatically

When a new node joins a cluster, IP addresses are used from the data LI

When a new node joins a cluster, the customer must give you IP addresses from the customer's local IP range.

When a new node joins a cluster, you must use "class A" subnet settings.

60. You create a LIF called svm_cifs_lif01 on a port that is already in an up state. After you test the storage failover, the LIF does not automatically revert to its home port.

In this scenario, what should you do to solve the problem?

Configure a new failover group.

Configure the LIF with the DHCP option.

Add the port in a broadcast domain.

Configure the LIF with the automatic revert option.

Page 7 of 12

61. Your customer wants a newly installed AFF C190 cluster to send SNMP notifications to a trap host called OVERWATCH01.

In this scenario, which two statements are correct? (Choose two.)

Configure an SNMP community string on the cluster.

Configure DNS on the cluster.

Configure a trap host on the cluster.

Configure a firewall policy and allow SNM

62. You have added two new AFF A250 nodes to an existing 4-node cluster with NetApp CN1610 cluster network switches. Although the nodes can join the cluster, the storage failover show command output shows that the NVRAM log is not synchronized, and it cannot reach the partner over an HA interconnect.

In this scenario, which two statements are true? (Choose two.)

The AFF A250 requires switches with 40GbE port support.

The AFF A250 uses different ports for the cluster and the HA interconnect.

The AFF A250 requires switches with 25GbE port support.

The AFF A250 uses the same port for the cluster and the HA interconnect.

63. You are installing a new AFF A400 cluster and need to access the cluster management LIF from a remote subnet with the fully qualified domain name (FQDN) a400.lab.netapp.com.

In this scenario, which two network components must be configured to log in to ONTAP System Manager from the remote subnet? (Choose two.)

route

NTP

DNS

VLAN

64. You are deploying an 8-node AFF A700 by using BES-53248 cluster switches. During the installation, you notice that ports higher than 16 are not coming online. You verify that the additional licenses are installed.

Which two additional steps must be taken to bring the additional ports online? (Choose two.)

Reload the firmware

Reload the RCF file

Re-enable each port

Reload the switch

65. You finished the installation of a 2-node cluster and want to determine whether HA is configured correctly.

What are two ways to accomplish this task? (Choose two.)

Use the OnCommand Performance Manager GU

Use the cluster ha show and storage failover show commands on the CL

Use the system node autosupport check show command on the CL

Use the OnCommand System Manager GU

66. What are two types of load balancing methods available in multimode interface groups? (Choose two.)

broadcast domain-based load balancing

IP-based load balancing

LIF-based load balancing

port-based load balancing

67. You are planning to install a new clustered Data ONTAP system for a customer.

Which action should be performed before configuring the cluster network switches?

Confirm IP address and configuration information for Brocade switches before configuring the switches.

Use the Cluster Network and Management Network Compatibility Matrix URL before configuring the switches.

Use the Inventory Collect Tool before configuring the switches.

Download the Fibre Channel switches software before configuring the switches.

68. Data ONTAP 9 supports which three features? (Choose three.)

SMB 3.0

NFSv2

SnapMirror

Infinite Volumes

69. A customer is installing a new system and has determined that they have a broken disk.

What information is required to open a NetApp Support case?

disk HBA firmware and serial number

mainboard rev. id

serial number or system ID

disk shelf serial number and shelf ID number

70. Which two default broadcast domain does the system create during initialization? (Choose two.)

Default

Cluster

Management

Node

Page 8 of 12

71. You want to add an AFF A400 HA pair to an existing cluster.

In this scenario, which LIF type is required?

cluster-mgmt

intercluster

data

node-mgmt

72. Click the Exhibit button.

You are preparing to replace a Cisco Nexus 92300YC switch. You have executed the cluster ping-cluster node1 command and received the output as shown in the exhibit.

Which two checks indicate that the cluster is ready for the replacement to be performed? (Choose two.)

2 paths up, 0 paths down (TCP check)

2 paths up, 0 paths down (UDP check)

larger than PMTU communication succeeds on 4 path(s)

basic connectivity succeeds on 4 path(s)

73. An administrator has physical ports e0e and e0f connected to 10GbE upstream switches. The e0c and e0d ports are connected to 1GbE upstream switches. All four ports are in the same broadcast domain.

The administrator wants to make sure that LIFs that need 10GbE cannot failover to 1GbE ports, but that LIFs that can use 1GbE or 10GbE can still failover to all four ports.

In this scenario, what should you do to accomplish this task?

Create two separate broadcast domains: one that contains e0e and e0f, and one that contains all four ports.

Create two separate failover groups: one that contains ports e0e and e0f, and one that contains ports e0c and e0d.

Create two separate broadcast domains: one that contains ports e0e and e0f, and one that contains e0c and e0d.

Create two separate failover groups: one that contains ports e0e, and e0f only and one that contains all four ports.

74. Which switch vendor is supported for the cluster network switches?

Juniper Networks

Cisco

Brocade

Hewlett-Packard

75. Click the Exhibit button.

A customer has a 4-node cluster and wants to know what will happen to their data if one of the two HA pairs goes down. Epsilon is configured and working properly and is owned by Node1. Nodes 3 and 4 have failed as shown in the exhibit.

What happens to the customer's data that is owned by the HA pair 3 and 4?

Nodes 1 and 2 will takeover the storage for nodes 3 and 4 and continue running normally.

The cluster will go into maintenance mode and only allow administrators access to data on nodes 1 and 2.

The entire cluster will panic and no data will be accessible.

The customer will lose access to the data on nodes 3 and 4 but will still have access to storage in nodes 1 and 2.

76. Your customer asks you how he can use the root aggregate to store data.

What should you tell him?

He can only use the root aggregate to store data if he changes the RAID group to RAID 4.

He can use the root aggregate only if he changes the name of the root aggregate to reflect a IP different aggregate naming convention.

He can use the root aggregate for storing any data.

He should not use the root aggregate for storing data, but create a new aggregate instead.

77. You are adding nodes to a 2-node switchless cluster. Before you add the nodes, which statement is correct?

You must install and configure the interconnect switches

You must enable and configure a cluster H

You must install and configure the cluster peering.

You must gather the port, IP address, and NTP information for the new node management LI

78. Exhibit:

While you are showing the NetApp Support website, your customer asks you to ensure that the new ONTAP storage array is covered by support before you complete the knowledge transfer procedure.

Referring to the exhibit, which two widgets would you select to accomplish this task? (Choose two.)

Systems

Contracts and Warranties

Active IQ

Product Support

79. Click the Exhibit button.

You are asked to install a new cluster with six FAS8060 nodes. While running Config Advisor, you see the messages shown in the exhibit. The customer does not want ACP cabled on their cluster.

Which two actions would allow the installation to be completed successfully? (Choose two.)

Advise NGS that the customer has a controller in an unsupported state.

Advise the customer that they must acknowledge that they are not using ACP on the installation.

Advise the sales team that the customer is operating without ACP and that the customer is asking you to leave it that way.

Advise the customer that the error will cause the controller to not operate properly and create an unsupported state.

80. You want to add two nodes to an existing 4-node cluster.

In this scenario, which two steps would you take to accomplish this task? (Choose two.)

Confirm that you do not reach the maximum node count.

Use Hardware Universe (HWU) to determine the correct cluster interconnect ports.

Confirm that the data switch has enough available ports.

Directly join the new controller to the current cluster.

Page 9 of 12

81. After properly cabling the NetApp CN1610 cluster switches, you see that joining the second node to a cluster fails because the node is not able to communicate with the other node.

In this scenario, what is causing this problem?

The cluster switches must be Cisco for more than two nodes in a cluster

The RCF file is not loaded properly

CN1610 is unsupported in newer ONTAP versions

The NTP server is not set

82. What does a clustered Data ONTAP SVM refer to?

the FlexArray controller that serves data in the cluster

the FlexArray controllers that serve data to clients

the virtual devices that serve data to VMware clients

the virtual devices that serve data in the cluster

83. Click the Exhibit button.

During an ONTAP cluster handover procedure, your customer asks how to identify and solve issues that might occur on the newly deployed array.

Referring to the exhibit, which two widgets would the customer use to help with these issues? (Choose two.)

Guide Me

Active IQ

Contracts and Warranties

ASE Corner

84. You have a 2-node FAS8300 ONTAP 9.8 cluster that serves SMB shares. You are configuring interface groups for higher performance and resiliency.

Which two NetApp best practices should you follow to satisfy these performance and resiliency requirements? (Choose two.)

Use ports from different NICs.

Use ports from the same NICs.

Use ports with different chipsets.

Use ports with the same chipsets.

85. Which two types of ports can host an intercluster LIF? (Choose two.)

Data

Intercluster

Network

Cluster

86. You have set up a new 2-node switchless cluster and want to verify that the failover is configured correctly.

In this scenario, which two commands accomplish this task? (Choose two.)

cluster ha show

storage failover show

cluster ring show

storage failover show-takeover

87. While installing a new AFF A400 HA pair, you are unable to add an NTP server from another subnet. You are able to ping the NTP server from the new cluster.

In this scenario, what are two causes of this problem? (Choose two.)

The admin SVM has the wrong gateway.

A firewall is blocking port 123.

The time skew is too great.

The cluster management LIF needs to be in a different IPspace.

88. Which license is required to enable storage failover?

CFO

no license is required

SFO

89. Which NetApp tool will simplify your initial system installation?

OnCommand Unified Manager

OnCommand System Manager

Config Advisor

System Setup tool

90. What is the minimum number of spares required in an "active-passive" FAS2200 HA pair where the "passive" controller has a RAID 4 root aggregate?

0 spare

1 spare

2 spare

Active-passive is NOT supported.

Page 10 of 12

91. Which feature provides preferred protection for the root volume of a storage virtual machine (SVM)?

SnapVault

load-sharing mirror

SnapMirror

SyncMirror

92. You must replace a FAS2750 switchless cluster with an AFF A220 switchless cluster for a customer. The customer requires that you transfer the data from the FAS2750 cluster to the AFF A220.

In this scenario, which two methods would you use to migrate the customer’s data? (Choose two.)

Establish an SVM-DR relationship between the two clusters and activate the destination SV

Remove all of the HDD drives from the FAS cluster and install them into the AFF cluster.

Install SAS cables between the two clusters and use the vol move command.

Provide cluster switches and build a 4-node cluster, then use the vol move command.

93. Click the Exhibit button.

After installation of a new ONTAP cluster, you experience a problem. You successfully create a support case on the NetApp Support site. The customer asks you how to view the status of the case.

Referring to the exhibit, which two steps would allow the customer to accomplish this task? (Choose two.)

Open https://support.netapp.com, using the partner credentials.

Open https://support.netapp.com, using the customer credentials.

Open My Cases, and select the 41747189 case number.

Open My Cases, and select Create a Case.

94. You are adding nodes to an existing cluster. In this scenario, which three statements are correct? (Choose three.)

If you are adding a second node to a single-node cluster, the second node must have been installed, but the cluster network can be configured later.

You must add a cluster switch for every two nodes.

If you are adding nodes to a multiple-node cluster, more than half of the existing nodes in the cluster must be healthy.

The switchless cluster functionality is supported only in a single or two-node cluster.

If you are adding nodes to a two-node switchless cluster, you must have installed and configured the cluster management and interconnect switches before adding additional nodes.

95. A host cannot connect to the namespace configured on an NVMe-enabled SVM.

In this scenario, what are two reasons for this problem? (Choose two.)

The namespace has not been added to the subsystem

The namespace has not be added to the igroup

The igroup has an incorrect NQ

The subsystem has an incorrect NQN

96. Click the Exhibit button.

You want to add an AFF A400 system to an existing 4-node cluster.

Referring to the exhibit, which number points to the ports that are used to cable the new nodes to the cluster interconnect switches.

97. You want to create a data volume on aggr0 and you receive a message with the following warning: ''Warning: You are about to create a volume on a root aggregate.

This may cause severe performance or stability problems and therefore is not recommended. Do you want to proceed?''

What is the reason for this severe performance or stability problem?

Controller failover and storage failover are separate processes that must occur in parallel, otherwise problems will arise.

The performance load generated by the data volume can be very strong, so it should not be shared with vol0 on aggr0, requiring a separate aggregate for it.

The performance load generated by the vol0 cannot be shared with any other volume on aggr0, requiring a dedicated aggregate for it.

Controller failover and storage failover are separate processes that must occur at different times, otherwise problems will arise.

98. A LIF can subscribe to how many failover groups?

99. You were dispatched to add a DS224C to an existing HA pair that has a stack of DS4243 shelves with 1 TB drives and a stack of DS4246 shelves with 1 TB drives. The customer wants to make sure that ACP is cabled for all shelves.

Which two considerations should you advise the customer in this situation? (Choose two.)

ACP communication uses SAS cables and does not require Ethernet cables for IOM12 and IOM6 modules.

ACP communication cannot be used for the DS224C and the DS4243 shelves at the same time.

In-Band ACP communication is use by default in ONTAP 9.0 and later software.

The ACP communication has been discontinued beginning with ONTAP 9.1, IOM6, and IOM12 modules.

100. You are preparing to install a new clustered Data ONTAP system.

Which tool prepares all the relevant customer and configuration information?

AutoSupport

Cluster Config Builder

OnCommand System Manager

Config Advisor

Page 11 of 12

101. A customer wants to reduce the disk allocation requirement for the root aggregate and increase usable storage by partitioning the disks into one large part and one small part.

The small part is used for the root aggregate and the large part for the data aggregates.

In this situation, what is this feature called?

ONTAP

storage virtual machine

Advanced Drive Partitioning

RAID

102. Which statement regarding Epsilon is true?

The node holding the epsilon has extra fractional vote weight.

Whenever a new node is added, the epsilon is automatically reassigned to this node.

The epsilon acts as a tiebreaker in a 2-node cluster.

Epsilon is reassigned automatically to the HA partner in case the current owner of the epsilon suddenly reboots.

103. Which statement about LIFs is true?

Cluster LIFs and data LIFs can share a port.

One cluster-management LIF exists per node.

One port can host multiple data LIFs.

A data LIF can be associated with multiple SVMs.

104. You want to support multiple tenants with duplicate IP addresses for your storage system.

Which statement is correct in this scenario?

You must create additional VLANs to use multiple tenants.

You must create an additional IPspace.

You cannot support multiple tenants on your storage system.

You must use different ports on your controller.

105. Click the Exhibit button.

Referring to the exhibit, you installed a new AFF A250 HA system with FC at a customer site. The customer asks how many ports can be used for the Ethernet host connections.

In this scenario, what would you tell the customer?

106. You want to add additional nodes to a cluster.

Which action will complete this task?

Run the node join command on the new nodes.

Run the cluster setup command on the new nodes.

Run the cluster join command on the existing cluster.

Run the cluster setup command on the existing cluster.

107. You are installing a 2-node clustered Data ONTAP system that has been shipped to the site in multiple boxes.

How do you find the disk shelves that contain the root volumes for each node?

The box for the shelf containing the root volume is yellow.

The box for the shelf containing the root volume is red.

The root volume is on the nodes, not the disk shelves.

The disk shelf’s sticker contains the controller’s serial number.

108. Click the Exhibit button.

A customer wants to replace their ONTAP cluster CN1610 switches with Cisco Nexus 3132Q-V switches. They want to perform a non-disruptive upgrade.

Referring to the exhibit, which cable will be required to non-disruptively migrate to the new switches?

a 10GbE SFP+ to SFP+ cable

a 100GbE QSFP28+ to 4x25GbE SFP28+ cable

a 40GbE QSFP+ to QSFP+ cable

a 40GbE QSFP+ to 4x10GbE SFP+ cable

109. A customer ordered a new ONTAP system and is concerned about how you will cable the system using multipath HA with the new system.

According to NetApp, what are the guidelines to accomplish this task?

Systems using hardware disk ownership can only be cabled using single path cabling practices.

Multipath HA is required on all HA pairs.

Multipath HA is required on all HA pairs except for some FAS25xx and FAS26xx system configurations.

Multipath HA cabling is required for SSD shelves.

110. An ONTAP cluster is installed at a secure site. The array has no access to the Internet but is managed 24/7 by onsite engineers. The customer requires that when hardware failures occur, the failures are reported to the NetApp Support team as quickly as possible.

In this scenario, which two tasks should be performed during the project hand-off procedure to satisfy the customer’s requirement? (Choose two.)

Ensure that Active IQ Config Advisor is installed.

Ensure that the onsite engineers receive EMS alerts when hardware issues occur.

Educate the onsite engineers about invoking the AutoSupport tool from ONTAP System Manager.

Educate the onsite engineer about how to manually log support calls.

Page 12 of 12

111. According to NetApp documentation, what should be used when using the Cluster Switch Health Monitor (CSHM) and log collection features?

Telnet

HTTP

SSL

SSH

TAGS:

NS0-184, NS0-184 exam dumps

Notify of

Label

Name*

Email*

Website

Label

Name*

Email*

Website

0 Comments

Oldest

Newest Most Voted

Inline Feedbacks

View all comments

Posts

Network Appliance Free Dumps

Get NS0-184 Dumps Full Version

Q&As: 371
Versions: PDF and Software Download Now

About Dumpsinfo

Dumpsinfo is a good platform providing the latest exam information and dumps questions for all IT certification exams. You can study all the latest exam dumps questions online.

[email protected]

Mon - Sat 9:00am - 6:00pm

2023 Network Appliance NS0-184 Exam Dumps Questions

Related

Posts

Network Appliance NS0-163 Exam Questions Simulate Actual NS0-163 Exam

Test Online NS0-700 Dumps Questions to Be Certified

Test Online NS0-404 Dumps Questions to Be Certified

Valid NS0-004 Exam Dumps are Your best Choice to Pass

About Us

EMAIL

Services

Opening Hours