CQE Dumps Guarantee You Pass CQE Exam Easily

Category:

ASQ Free Dumps

Comments:

0 Comments

Post Date:

May 22, 2025

As new threats and vulnerabilities emerge, the CQE exam is updated to reflect the latest trends in ASQ Certification. By using CQE exam dumps questions, you can ensure that you're staying up-to-date with the latest exam content and are fully prepared to address new challenges in Quality Engineer Exam. ASQ CQE exam dumps questions can help you optimize your preparation and ensure that you're fully prepared for the exam. Practice free ASQ CQE exam dumps questions below.

Page 1 of 6

1. Which of the following activities is a critical component of the closing meeting of an external audit?

Determining appropriate corrective actions to take

Establishing the date for a follow-up audit

Distributing the final audit report

Providing an explanation of the findings

2. A way to convince management that a quality improvement program is needed is to present

the number of audit findings the company received from the last audit

the company's performance in terms of quality in comparison with its competitors

die size of the problem in terms of the potential savings and increased profit that can result from fixing it

data on how employees will produce better quality product and services if their pay is increased and their benefits improved

3. The producer's risk can be determined from the

acceptance quality limit (AQL)

lot tolerance percent defective (LTPD)

average outgoing quality limit (AOQL)

rejectable quality level (RQL)

4. Which of the following results is an advantage of a ship-to-stock program?

It replaces scheduled audits with incoming inspection.

It reduces shipping costs.

It reduces dock-to-line time.

It reduces the need for purchaser supplier interaction.

5. Working on ail design phases simultaneously is characteristic of

design for six sigma

design for reliability

quality function deployment

concurrent engineering

6. What type of audit should be used to determine how well an organization's activities conform to its quality program?

Process

Product

System

Third-party’

7. Temperature measured in degrees centigrade is an example of what type of measurement scale?

Ratio

Nominal

Ordinal

Interval

8. Which of the following actions best describes quality function deployment (QFD)?

Determining if quality procedures are being followed on the shop floor

Determining which processes are functioning correctly

Linking customer requirements to product features

Reducing costs of a product and product features

9. In an ISO-compliant quality system, which of the following methods would be most effective for identifying employee training needs?

Allowing employees to identify their own training needs

Conducting a needs analysis for each job category

Requiring all employees to complete the same training courses

Requiring supervisors to identify training for their employees

10. A system to capture product revisions that must be tracked is more commonly known as

work instruction control

procedure control

batch control

change control

Page 2 of 6

11. In a sample of 2.000 items taken from a large lot. 80 are found to be nonconforming.

What is the 95% confidence interval for the proportion of nonconforming items?

[0.0328. 0.0472]

[0.0314. 0.0486]

[0.0308. 0.0499]

[0.0302. 0.049

12. Which of the following symbols represents process performance index?

Cpk

ppk

13. Analysis of data on all product returns is important because

I. Failure rates change with length of product usage.

II. Changes in design and in customer use are often well reflected.

III. Immediate feedback and analysis of product performance becomes available.

I only

I and III only

II and III only

I, II and III

14. Typically Pareto diagrams are used for which of the following reasons?

I. To display the significant few categories.

II. To compliment attribute data charting.

III. To eliminate insignificant categories.

IV. To focus attention in priority order.

I and III only

I, II and III only

II, III and IV only

I, II, III and IV

15. Which of the following tools is effective for evaluating all possible causes of a problem and isolating the probable causes?

Pareto chart

Control chart

Scatter diagram

Fishbone diagram

16. Which of the following tools specifies the use of a feedback cycle?

Flowchart

Cycle-time reduction

Gantt chart

Plan-do-check-act

17. An inventory list of laptops in a sales office is an example of which measurement scale?

Nominal

Ordinal

Interval

Ratio

18. Registration to the ISO 9001 standard requires which of the following types of audit?

Process

Product

Second-party

Third-party’

19. A company is designing a production process for a new consumer product. To ensure that the product will be traceable from design and production through end-user receipt and use. the company must develop a system for product

review

packaging

identification

storage

20. The table below shows the results of inspecting 3,752 items. On the basis of this information, a Pareto chart would show what cumulative percent of nonconformities by the end of the third operation? Calculator

16.2%

21.7%

78.3%

90.0%

Page 3 of 6

21. Which of the following statements BEST describes a bimodal distribution?

This distribution shows stratified data and two distinct peaks.

This distribution shows a single mode and bell shaped distribution.

This distribution is truncated.

This distribution has several distribution peaks.

22. A customer rates its suppliers for which of the following reasons?

To negotiate the lower cost of a purchased good

To compare multiple sources of the same item

To eliminate incoming inspection

To increase inventory levels

23. Accelerated aging of a sterile barrier system is an example of which or the following design verification methods?

Analyzing

Testing

Demonstrating

Inspecting

24. Using the model for prediction

1,3,2,4

1,4,2,3

2,4,2,1

3,2,4,1

25. A process has the following output characteristics:

Mean = 28.65

Median = 24

Mode = 20

The uniniodal distribution with these characteristics is defined as

skewed left

skewed right

not skewed

s-shaped

26. The probability of an accident for the head event "H" given below is:

0.0700

0.1125

0.0689

0.1100

27. Under a defect classification system, a nonconformance that could cause a product's usability to be substantially reduced would be classified as

acceptable

minor

major

critical

28. A facilitator asks each team member in turn to suggest one idea during a brainstorming session.

This is an appropriate method to use when

senior managers are present

team members have been sitting for an extended time period

tight deadlines need to be met

dominant members are stifling others

29. Risk control includes making decisions using which of the following pieces of information?

Acceptable levels of risk

Fault tree analyses results

Check sheet comparisons

Analysis of experiments

30. A process that is in statistical control has the following characteristics.

X 122

J? = 2!

n = 5

What are the upper and lower control limits for the A'chart of this process?

UCL = 12.72. LCL = 11.68

UCL 13.25. LCL 11.15

UCL = 13.41. LCL = 10.99

UCL - 14.30. LCL 10.10

Page 4 of 6

31. The following chart is being used to monitor a process.

What do points X and Y. and region Z represent on the chart?

Special causes of variation

Changes in raw materials

Common causes of variation

Statistically stable variation

32. When nonconforming items are found, which of the following actions should be taken first?

A Retest

Destruction

Identification

Return to supplier

33. Which of the following tools can be used to show a frequency distribution?

An affinity diagram

An interrelationship digraph

A PERT chart

A check sheet

34. A system was designed with 3 capacitors. When the system is first activated all capacitors are operating. The system continues to operate as long as at least 1 capacitor is operating.

This is an example of

Redundancy.

A series system.

An active parallel system.

A standby parallel system.

35. During the causes of a problem have been verified in the analysis phase of a six sigma project, they will form the basis of the solution in Much of the following phases?

Control

Define

Improve

Measure

36. The following is an incomplete ANOVA table.

Source ss df MS F

Treatment 333 4

What is the value of the F-statistic used to test for differences in treatment?

0.21

1.07

2.87

5.37

37. After attempting to prevent or control risk, which of the following types of risk will remain?

Inherent

Residual

Control

Credit

38. A material review board (MRB) gets its authority to act from which of the following functions?

Executive management

Purchasing

Engineering

National or international standards

39. A production line has job aids that outline, step by step, how to perform the tasks of the job. This is followed by each of the operators working on the line.

This is an example of

take time

standardized work

value stream mapping

40. Two advantages of process mapping are the ability to

I. Visualize the process being described.

II. Discover manufacturing problems only.

III. Discover quality problems only.

IV. Check current processes for duplication or redundancy.

I and IV only

II and III only

I and III only

II and IV only

Page 5 of 6

41. If a quality engineer discovers a situation in which unlabeled finished product could be shipped to customers, what would be an appropriate preventive action to take?

Train the shipping department staff in quality tools and techniques

Identify the unlabeled product and have it labeled

Form a team to error-proof the process

Conduct a backward trace of the process

42. Which of the following statements is true regarding a failure mode and effect analysis (FMEA)?

A FMEA is a pictorial representation of the reliability interdependency of components.

A FMEA should not get updated throughout the life cycle of the product.

The advantage of a FMEA is to communicate the risk with different stakeholders.

The first step in the development of an FMEA is to calculate the Risk Priority Number (RPN).

43. Which of the following tools can be used to evaluate the normality of a data set?

Probability plot

CUSUM chart

Box and whisker chart

Kruskal-Wallis rest

44. The following data sets were presented to top management.

Which problem area should be targeted for improvement first?

45. Four ingredients are blended to make a final product. Using the data below, what is the expected weight and variation of the final product?

Ingredient A 70 ± 3.00 grams

Ingredient B 20 ± 1.73 grams

Ingredient C 15 ± 1.73 grams

Ingredient D 10 ±- 1.00 grams

115 ± 7.46 grams

115 ± 5.73 grams

115 ± 4.00 grams

115 ± 3.61 grams

46. Which of the following information should be contained in work instructions?

Training requirements

Production cost formulas

Design review formulas

Equipment needed to do the work

47. Which of the following is the most important aspect of a successful quality improvement effort?

Employee participation

Financial comminnent

Management commitment

Organizational need

48. What type of test should be used to detect certain kinds of subsurface flaws?

Visual inspection

Liquid penetrant

Magnetic particle

Rockwell

49. A comprehensive corrective action program is initiated at a large company. Input for CARs are received from customers, internal and external audits, material review reports and other sources.

Which two of the following groups would usually administer and control the CAR process?

I. Management review team.

II. Quality department.

III. Corrective Action Board.

IV. Material Review Board.

I and II only

I and III only

II and III only

III and IV only

50. In a value stream analysis, inspection is typically classified as

real value added

organizational value added

non-value added

customer value added

Page 6 of 6

51. A company is developing a machine that has many modules. Each module works as intended, but when placed in the machine the system performs at less than desired levels. System changes have further optimized each module, but overall system optimization has continued to decline.

This is an example of

a feasibility study

a SWOT analysis

a PEST analysis

an unintended consequence

52. Which of the following tools can be used to classify or determine a safety quality characteristic?

An inspection plan

A criticality analysis

Standard work instructions

A control chan

53. Which of the following tools can be used to communicate performance data in time sequence?

Scatter diagram

Pareto chart

Control chart

Flowchan

54. The following summary of data represents the amount of time customers spend in a store between the hours of noon and 1:00 p.m. during a one-month period. Time (minutes) Number of customers

The summary is an example of which of the following?

Stem-and-leaf plot

Box plot

Pareto chart

Frequency distribution

55. Which of the following problem-solving tools is a column graph which displays a static picture of the process?

Pareto chart.

Control chart.

Histogram.

Cause and effect diagram.

TAGS:

CQE, CQE exam dumps

Notify of

Label

Name*

Email*

Website

Label

Name*

Email*

Website

0 Comments

Oldest

Newest Most Voted

Inline Feedbacks

View all comments

Get CQE Dumps Full Version

Q&As: 175
Versions: PDF and Software Download Now

About Dumpsinfo

Dumpsinfo is a good platform providing the latest exam information and dumps questions for all IT certification exams. You can study all the latest exam dumps questions online.

[email protected]

Mon - Sat 9:00am - 6:00pm

CQE Dumps Guarantee You Pass CQE Exam Easily

Related

Posts

Pass CCQM Exam to Get ASQ Certification

Get Certified Easily with Online CSQE Dumps

Study Online CSSBB Exam Dumps to Pass

About Us

EMAIL

Services

Opening Hours