Prepare HPE4-A52 Exam with Using HPE4-A52 Dump Questions

Category:

HP Free Dumps

Comments:

0 Comments

Post Date:

June 15, 2025

If you are serious about passing your HP HPE4-A52 certification exam, practicing with HPE4-A52 dumps questions is an essential step in your preparation process. These HPE4-A52 dumps will help you assess your knowledge, identify your strengths and weaknesses, and improve your chances of passing the exam on the first try. So why wait? Start practicing today and give yourself the best possible chance of success! Test free HPE4-A52 exam dumps questions below.

Page 1 of 8

1. Set DSCP value EF (46) on all egress packets from VLAN 20 for high-priority traffic.

See the Explanation.

2. Restrict specific commands for network admins using TACACS+ command authorization.

See the Explanation.

3. Create a dynamic forwarding rule using user role returned by ClearPass to determine if user traffic should be tunneled or locally bridged.

See the Explanation.

4. Implement a dynamic role that tunnels guest traffic but allows internal employees to route locally.

See the Explanation.

5. Troubleshoot OSPF neighbor not forming due to area mismatch.

See the Explanation.

6. Protect the switch CPU by dropping all unnecessary Telnet traffic at the control plane.

See the Explanation.

7. Enable device pre-provisioning in Aruba Central before the switch connects.

See the Explanation.

8. An attacker is generating high volumes of ICMP packets. Create a CoPP rule to rate-limit ICMP to 100 pps to preserve switch resources.

See the Explanation.

9. Configure per-device VLAN assignment using MPSK. HR uses VLAN 100, IT uses VLAN 200.

See the Explanation.

10. Implement Weighted Round Robin (WRR) scheduling across queues 1C4.

See the Explanation.

Page 2 of 8

11. Create a role called "netadmin" that allows configuration access to VLANs and interfaces only.

See the Explanation.

12. Configure IGMP snooping for VLAN 50 to ensure multicast is not flooded.

See the Explanation.

13. Configure iBGP between two core Aruba CX switches in AS 65000 and ensure loopback interfaces are used for peering.

See the Explanation.

14. Enable heartbeat monitoring for gateway clustering to detect failures faster.

See the Explanation.

15. Enable storm control to protect against broadcast storms on interface 1/1/15. Limit broadcast to 5%.

See the Explanation.

16. Shape traffic for VLAN 30 to 5 Mbps while allowing burst up to 7 Mbps.

See the Explanation.

17. Enable CoA (Change of Authorization) to disconnect sessions when a user is disabled in ClearPass.

See the Explanation.

18. Configure a guest SSID with captive portal redirection to ClearPass for web authentication.

See the Explanation.

19. Configure a switch to trust DSCP values from IP phones connected to access port 1/1/5.

See the Explanation.

20. Simulate multicast receiver join and verify PIM tree formation using logs.

See the Explanation.

Page 3 of 8

21. Configure VSF on two Aruba 2930F switches connected via ports 1/1/49 and 1/1/50.

See the Explanation.

22. Configure ECMP for a specific static route with two next hops.

See the Explanation.

23. Configure Anycast BGP between three core routers sharing the same loopback prefix.

See the Explanation.

24. Audit all QoS settings and policies applied to a switch for a security review.

See the Explanation.

25. Enable queue monitoring and set threshold alerts for Queue 7 utilization above 90%.

See the Explanation.

26. Configure an AP group with both tunneled and bridged SSIDs for different client requirements.

See the Explanation.

27. Configure an Area Border Router (ABR) for OSPF between backbone and stub area.

See the Explanation.

28. Verify ECMP load balancing across uplinks to a remote network.

See the Explanation.

29. Use ACL to block ICMP echo requests from specific subnet (192.168.50.0/24) to the switch.

See the Explanation.

30. Monitor CoPP counters to detect how many packets are dropped by the current policy.

See the Explanation.

Page 4 of 8

31. Configure Dynamic Segmentation fallback behavior when ClearPass is unreachable.

See the Explanation.

32. Validate reachability and segmentation between two hosts in different VXLAN segments using ping and traceroute.

See the Explanation.

33. Reduce bursty traffic impact by enabling shaping and buffering for social media (e.g., port 443 with known domains).

See the Explanation.

34. Configure an Anycast gateway IP 10.1.1.1/24 across two Aruba CX switches using VSX.

See the Explanation.

35. Troubleshoot a failed 802.1X authentication for a known good user.

See the Explanation.

36. Troubleshoot a case where clients are being assigned VLANs but cannot reach the internet.

See the Explanation.

37. Use route maps to set BGP community on advertised networks.

See the Explanation.

38. Implement policing for guest VLAN traffic to drop traffic above 2 Mbps rate.

See the Explanation.

39. Set an Aruba CX switch as secondary root bridge for VLAN 200.

See the Explanation.

40. Configure passive interfaces in OSPF to prevent unnecessary hello traffic.

See the Explanation.

Page 5 of 8

41. Deploy multicast source-specific multicast (SSM) filtering for security.

See the Explanation.

42. Simulate and detect a broadcast storm in a lab VLAN using Aruba CX tools.

See the Explanation.

43. Enforce port security using NAC to limit a port to a single MAC address dynamically learned.

See the Explanation.

44. Configure a switch to fall back to MAC authentication if EAP-TLS authentication fails.

See the Explanation.

45. Simulate a failed ECMP path and verify traffic reroutes automatically.

See the Explanation.

46. Configure redundancy between two gateways using VRRP for tunnel termination.

See the Explanation.

47. Troubleshoot a high-latency issue by checking queue buildup on uplink interfaces.

See the Explanation.

48. Identify asymmetric traffic on MC-LAG and balance it.

See the Explanation.

49. Verify peer consistency after restoring VSX config.

See the Explanation.

50. Monitor client mobility between clustered gateways to ensure seamless roaming.

See the Explanation.

Page 6 of 8

51. Troubleshoot a situation where broadcast storm control is dropping traffic unexpectedly.

See the Explanation.

52. You want to allow routing protocols like OSPF and BGP unlimited access to the control plane while limiting others. Create a CoPP policy that prioritizes OSPF and BGP.

See the Explanation.

53. Enable EAP-TLS with certificate-based authentication and validate trust chain.

See the Explanation.

54. Implement Distributed LAG (MC-LAG) between a server and two Aruba CX switches in VSX.

See the Explanation.

55. Configure OSPF authentication using a plaintext key for area 0.

See the Explanation.

56. Implement a basic GBP (Group-Based Policy) that allows web clients (group 10) to talk only to web servers (group 20) on TCP port 443.

See the Explanation.

57. You are tasked with creating a Central group in Aruba Central for all access switches at HQ. Name it "HQ-Switches".

See the Explanation.

58. Identify and isolate a loop on the network using STP topology commands.

See the Explanation.

59. A Layer 2 attack is flooding CAM tables with spoofed MACs. Enable port security to limit MAC learning per port.

See the Explanation.

60. Configure loopback interface as the source for all VXLAN VTEP operations.

See the Explanation.

Page 7 of 8

61. Show all MAC addresses learned via VXLAN using EVPN.

See the Explanation.

62. A new switch needs to be automatically provisioned using ZTP. Describe the steps to enable ZTP on the switch.

See the Explanation.

63. Monitor distributed LAG bandwidth usage.

See the Explanation.

64. Shape all video traffic marked with DSCP AF41 to 20 Mbps.

See the Explanation.

65. Force edge port recovery after BPDU-induced shutdown.

See the Explanation.

66. Configure root guard on VLAN 30 to prevent a rogue switch from becoming STP root.

See the Explanation.

67. Simulate OSPF route redistribution into a multi-area OSPF setup.

See the Explanation.

68. Design summarization between OSPF areas at the ABR.

See the Explanation.

69. Troubleshoot ZTP failure.

What CLI command helps you verify whether the switch received DHCP and contacted Central?

See the Explanation.

70. Manually push a configuration from Aruba Central to a switch after making changes.

See the Explanation.

Page 8 of 8

71. Enforce QoS only during congestion. Use default queue but mark excess traffic with lower DSCP.

See the Explanation.

72. Prevent a misbehaving host from sending high-priority DSCP values. Override all ingress traffic to default DSCP 0.

See the Explanation.

73. Verify if EVPN peers have established and exchanged MAC routes correctly.

See the Explanation.

74. Configure multiple storm control types (broadcast, multicast, unicast) on the same interface.

See the Explanation.

75. Configure local fallback for AAA so that if the TACACS+ server is down, local credentials are used.

See the Explanation.

76. Monitor VSX keepalive failures and take action.

See the Explanation.

77. Prevent MAC spoofing attacks by allowing only known MAC addresses on port 1/1/15.

See the Explanation.

78. Bind template variables (hostname, IP, mask) to a specific switch MAC in Aruba Central.

See the Explanation.

TAGS:

HPE4-A52, HPE4-A52 exam dumps

Notify of

Label

Name*

Email*

Website

Label

Name*

Email*

Website

0 Comments

Oldest

Newest Most Voted

Inline Feedbacks

View all comments

Get HPE4-A52 Dumps Full Version

Q&As: 260
Versions: PDF and Software Download Now

About Dumpsinfo

Dumpsinfo is a good platform providing the latest exam information and dumps questions for all IT certification exams. You can study all the latest exam dumps questions online.

[email protected]

Mon - Sat 9:00am - 6:00pm

Prepare HPE4-A52 Exam with Using HPE4-A52 Dump Questions

Related

Posts

HPE2-B03 Dumps Questions – Effective Way to Get Certified

Advance Your Career by Using Online HPE2-N70 Dumps

HPE7-A10 Online Dumps Boost Your Career

Improve Your Knowledge with HPE6-A86 Exam Dumps

About Us

EMAIL

Services

Opening Hours